Book Your Installation

 

 

Just about every person has got their own unique opinion about Tools You Need to Install a New Bathtub .

Mounting a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old tub is readily obtainable, the job can move easily; if you have to open up a wall to remove the old bathtub and position the new bath tub, the job is much harder. In either instance, the job is within a house handyman's skills, although you will certainly require a helper to vacate the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the job and also fit attempting it. As opposed to employing a service provider to take control of a halfway-completed project, it is far better to think about employing one prior to you begin. Opportunities are you might need a specialist plumber to make tube connections.
This write-up will help you mount a new bath tub in your shower room if you have currently purchased a brand-new tub and also don't require to alter the arrangement of your previous water system pipes.
Your devices as well as product checklist need to make up the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipeline Caps


 

Getting ready for the Installation

First of all, the sustaining framework provided with the bath needs to be fitted (if required) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is necessary to ensure that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be fitted in its final setting.

 

 

Removing Old Touches

If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, switch on the faucets to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be quite troublesome because of the limited access that is frequently the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have been eliminated, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning during this process. When the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing substance.
Prior to moving on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.

 

 

Installing the Bathtub

Making use of both wood boards under its feet, put the bathtub in the required placement. The wood boards are practical in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by inspecting the spirit level and readjusting the feet on the tub until the spirit level checks out level.
To mount faucets, fit all-time low of the furthest versatile tap adapter to the ideal supply pipeline by making a compression join; then do the very same for the various other faucet.
Turn on the supply of water and examine all joints and also brand-new pipework for leaks and tighten them if essential. Load the tub and also examine the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the bathtub needs to wait up until the tub has been made use of a minimum of once as this will certainly settle it into its last setting.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin ensuring that the washers remain in location in between the tap and also the sink. Protect the faucet in place with the supplier supplied backnut. Once the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Tiling Around the Bathtub

In the location where the bathroom meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to split an inflexible seal, causing the water to permeate the wall surface in between the bath as well as the tiling, causing difficulties with wetness and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to permit the activity experienced when the tub is in use. The sealer can fracture fairly early if you do not take into consideration this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof adhesive and grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

We had been shown that article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround from a friend on a different web page. Are you aware of another person who is intrigued by the topic? Please feel free to share it. Bless you for your time. Come back soon.

Additional Information